Qingdao Honghesheng Industry Co., Ltd.
Service as the basis, quality as the survival, science and technology for development
Add to Cart
Rubber Vulcanizing Machine
220v 380v 410v 50hz full automatic electric heated rubber autoclave are divided into two series: steam vulcanizing boiler series and hot air vulcanizing boiler series.
Each series has three heating mediums: steam, electric and conduction oil.
Working principle for cold type retreading tyre curing chamber
The steam enter into the steam diffusion tube by entrance of steam which at the bottom of the steam vulcanizing boiler and the entrance can be controlled by automatic valve. The steam diffusion tubes vertical arrangement in the bottom of the tank. The small holes which diameters are 3mm,4mm and 5mm on the steam diffusion tube are arranged according to certain rules and angel to ensure that the steam spread in the tank evenly. Thus it can prevent the different quality of the product because of the uneven steam. After set working procedures, the heating, heat preservation, vulcanization and etc can be finished by automatic control system. The equipment stop working and give alarm after all procedures finished.
Working principle for electricity steam vulcanizing autoclave
Electric heated tubes are arranged in the bottom of the tank according to certain rules, the heat exchanger linked the electric heated tubes and the water channel. The height of the sink is 5~15mm. The steam which produced by electric heated tubes and water spread from down to up evenly until turn into condensate water pour into the sink after touched the wall of tank and then heat again. The temperature of the tank evenly and the pressure has no error, so it can prevent the different quality of the product because of the uneven temperature and pressure. After set working procedures, the heating, heat preservation, vulcanization and etc can be finished by automatic control system. The equipment stop working and give alarm after all procedures finished.
Working principle for steam hot-air vulcanizing autoclave
The steam enter into the cooling fin which in the tank of the steam hot-air vulcanizing by two sets of automatic valve. The cooling finds arrangement in the tank according to the certain rules. The draught fan which in the back of the tank make the quantity of heat spread evenly by special temperature cycle plates. Heat cycle form even temperature field. Thus it can prevent the different quality of the product because of the uneven temperature and pressure. After set working procedures, the heating, heat preservation, vulcanization and etc can be finished by automatic control system. The equipment stop working and give alarm after all procedures finished.
Working principle for electricity hot-air vulcanizing autoclave
Electric heated tubes which controlled by N groups of separate switch are arranged in the bottom of the tank according to certain rules. Only keep one or two groups of electric heated tubes working after reached working temperature, so it can save the energy and reduce the cost greatly. The temperature of the tank evenly and the pressure has no error, so it can prevent the different quality of the product because of the uneven temperature and pressure. After set working procedures, the heating, heat preservation, vulcanization and etc can be finished by automatic control system. The equipment stop working and give alarm after all procedures finished.
Parameter For Reference
Type:horizontal ,vertical
Heating Ways:steam heat ,thermal oil heating ,elecricity heating ,electric heating air
Temperature :150-220 degree
Pressure:0.6-3.0Mpa
Operation ways:automatic
Diameter:600-4500mm
Length: any length is ok
Safety Device:automatic discharge pressure ,automatic feed water ,automatic alarm, the door has double safty interlock device
Features
Uniform insite layout to make sure hot air flow and heating uniformity
Guide flow cover which disperse heat uniformity&circulate High temperature circulation fan blow heat from back to front uniformity
Why to choose us?
1.Our ram material is national goverment pointed facmous steel factory ,and standard pressure vessel special plate ,Q345R .Each steel is tested before leaving factory .It have good bear pressure
2.heating area is uniform ,according to your working technology to design inside heating system ,we have special design heating sink ,,it is arranged in the up side ,bottom ,left side ,right side ,
3.Adopt external insulation ,the galvanized sheet is welded around the tank (it wont rust within 10 years),inside are 80mm insulation cottom ,heat insulation head add 60mm thermal insulation , then add fixed bolt .To make inside heating value can be used enough ,and reduce consumtion , save cost . and it is easy for transportation.
Detailed Pictures
Since the price of raw materials will fluctuate in different periods, the online price is a reference price, not the final price.
We can guarantee the same quality and the lowest price among our peers. If you are interested in our products, please feel free to contact us, we will give you a real-time quotation A.S.A.P.
Q: How to send your enquiry? Kindly tell me the answer...
-1) What product do you vulcanize?
-2) What's the length and diameter of tank do you need?
-3) Max heating temperature and pressure,pls?
-4) Leave me your WhatsApp,Skype or WeChat.